Q-wiz Tech Support

About

Brain-Trainer Wiz User Guide (1.94 MB)
Wiz by Pocket Neurobics – User Manual

How To

Setup

If your Wiz device was purchased from Brain-Trainer you should have an amplifier or Wiz setup file. Check your Brain-Trainer account. If the Wiz is not properly installed, it may be that the PN driver is missing.

PN Wiz Driver Installation

This will install the PN wireless dongle driver.

  1. Turn off antivirus program and firewall.
  2. Download this PN Wireless Dongle Driver file:  PN executable driver file. Extract and right-click and run as administrator.

If not successful, see instructions below for manual installation.

Port assignment

You can find or change the COM port assignment for your Wiz device. Open Device manager and look under Ports (COM & LPT) to see what COM port your Pocket Neurobics device has been assigned.

Some computer brands like to reserve COMs 1, 2 and 3 for their own use. If no COM ports are used, a new install enumerates the next available port (normally COM3). To avoid conflict, you can change the port assignment manually.

Open Device manager. In the search field type “Device manager” and select it.

search for device manager

In Device Manager, click Ports (COM & LPT). Note the COM port number assigned.

Open Properties. Right-click on the Pocket Neurobics Wireless Dongle entry and choose Properties.

Select Port Settings tab.

Click Advanced button.

Select new COM port number. On the COM Port Number field change the COM port to another port higher than 3 to avoid conflict and click OK.

Reinsert Wiz cable. Disconnect the Wiz cable from your computer’s USB port and connect it again.

See how:

PN Driver Manual installation for stubborn drivers

Turn off antivirus program and firewall.

Save this file to your computer: Pocket Neurobics driver

This file is the original pnWirelessDongleDriver EXE file for Windows 10 and earlier. The .exe extension has been changed to .zip so that it can be extracted and used for manual installation.

Save this file to your Downloads folder. You will browse to it during the installation process.

Extract the files. In your Downloads folder, right-click on the file and select “Extract All” (or for 7-Zip “Extract Here“).

Update the Driver

Connect the Wiz device to your computer.

Open Device manager. In the search field type “Device manager” and select it.
search for device manager

Expand Other devices section. In Device Manager, click Other devices.

Open Update window. Right-click on the entry there. It could say USB Serial Port or Q-wiz. Click Update Driver.

update driver

Select Manual search. In the Update Driver window, choose Browse my computer for driver software

browse for driver

Do not see Other devices, USB Serial Port or Q-wiz but do see Ports (COM & LPT), Pocket Neurobics Wireless Dongle? Skip to Configure USB Protocol.

Browse to PN driver folder. In the next window, click the Browse button and navigate to the location of the extracted folder

Downloads\pnWirelessDongleDriver_Install_XP_Vista_Win7

Be sure you are in the pnWirelessDongleDriver_Install_XP_Vista_Win7 folder.

Click OK .

Click Next.

Configure USB Protocol

Now you will repeat those steps to configure the USB protocol.

Open Update Driver window. Right-click on the Pocket Neurobics Wireless Dongle  or Q-wiz  or similar entry and choose Update Driver Software.

update driver

Select Manual Search. In the Update Driver window, choose Browse my computer for driver software

browse for driver

Browse to PN driver folder. In the next window, click the Browse button and navigate to the location of the extracted folder above

Downloads\pnWirelessDongleDriver_Install_XP_Vista_Win7  and click OK and Next.

Finish Driver Installation

Note COM port number. Now, in Device Manager you will see:

Under Universal Serial Bus controllers, %USB\VID_0403&PID_6001.DeviceDesc%
Under Ports (COM & LPT), Pocket Neurobics Wireless Dongle (COMx) or possibly Q-wiz or similar. Note the COM port number for use in BioExplorer Device setup.

If you do not see “Pocket Neurobics Wireless Dongle” or “Q-wiz” or other recognizable name, repeat this process one or two more times, Properties > update driver > browse to folder until you see it.

view of device manager

Reinsert Wiz cable. Disconnect the Wiz cable from your computer’s USB port and connect it again.

If you do not find the expected PN / Wiz driver entry under Ports, try turning off Core Isolation Memory Integrity.

Turn off Core Isolation Memory Integrity
  1. Go to Security > Windows Security > Device Security > Core Isolation Details > Memory Integrity Settings.
  2. Turn Memory Integrity Settings “Off.”
  3. Reboot the computer.

Reset Q-wiz to factory settings

To set the Q-wiz back to factory settings follow these steps:

  1. Disconnect the Q-wiz from the computer
  2. Hold the mode button down (on the top end of the Q-wiz) while at the same time you connect the Q-wiz to the computer.

Firmware  Update

Firmware files are downloaded to a directory on your computer. We suggest saving in Downloads. The firmware page is no longer active on the manufacturer’s website. The most recent firmware file we have available at brain-trainer is version 9x below.

Then there are several mechanisms to download the file into the Wiz. The Wiz needs to be placed into Program Mode to allow the download to proceed. Use the Wiz settings window to select Program Mode.

Update using BioExplorer software
  1. Open BioExplorer.
  2. Connect Wiz to USB port.
  3. Open BioExplorer > Devices. This opens the Device Manager.
  4. Select PN wiz as a device if it is not already selected and double-click the name to open Device Properties and check that the correct COM port is selected.
  5. Click the PN Wiz tab.
  6. Set Wiz to Program mode by selecting Program on the Wiz window.
  7. Now select Upload firmware in the Device Properties window.
  8. Navigate to the folder where you saved the firmware file and select the file.
  9. Select Open and allow the Wiz to update.

Upon completion, the last line of the update in the Properties window should say SUCCEEDED and the Wiz window will show Mode changed from Program to EEG.

We use 4 channel mode (256 samples per second) for HEG and EEG so it can be set to 4 channel mode now. Click OK and close the window.

Update using BioEra software
  1. Place the Wiz in Program Mode.
  2. Load a ‘BioEra for Windows’ Wiz design.
  3. In the design view, right click on the “PN_Wiz” object and select “Advanced Properties”.
  4. You will see an item “Firmware File Path”. Locate the firmware file to upload to the Wiz.
  5. Then click “Upload Firmware”

Progress of the file upload is not indicated, however as above, success will be indicated by the Wiz starting to transmit in Mode 2.

Update without BioExplorer or BioEra

To update the firmware for your Q-wiz without using BioExplorer or BioEra software, first download the stand-alone Firmware uploader utility below.

1.  Put the Wiz in Program mode. On the Q-wiz, press the Mode button on the Wiz to change the mode. 1 blink of the mode light indicates Mode 1, 4 blinks is Mode 4, 0 blinks is Mode 0- Program Mode.

2.  Run the firmware uploader utility. Double-click to run the firmware uploader utility. Use the following serial port properties:

38400 Baud
8 bit
1 start bit, 1 stop bit
No parity
The COM Port assigned to the Wiz driver by Windows (Device Manager > COM & LPT Ports)

3.  Navigate to find the saved file on your computer. It will be in your Downloads folder if that is where you saved it.

[ if there is an error message about missing files then see here..
http://superuser.com/questions/519841/getting-msstdfmt-dll-missing-when-starting-visual-basic-6-application ]

Video below: Using BioExplorer to check version and update

Need Help With Choosing A Neurofeedback System That’s Right For You?

Request A FREE Consult & Get All Of Your Questions Answered Today

Get The Latest Updates & 2 FREE Instant Downloads: The Efficacy of Neurofeedback & The 5 Myths That Block Clinicians From Offering Brain Training, Sign Up Now!

We use cookies on this site to enhance your user experience.

By using this site, you are giving your consent to set cookies. Privacy Policy

0
Your Cart